MOCpages : Share your LEGO® creations
LEGO models my own creation MOCpages toys shop On Round Tower TechniquesCastle
Welcome to the world's greatest LEGO fan community!
Explore cool creations, share your own, and have lots of fun together.  ~  It's all free!
On Round Tower Techniques
About this creation

The Quest for the Round Tower

In 2008, I challenged myself to devise a method for creating round towers that could supplant the current methods. After one epiphany and a couple years of procrastination, Deborah Higdon beat me to the punch. But after the number of adherents to her technique started to grow, I was inspired to build again.

Of course, in order for my techniques to catch on, first I have to show people how they are done. So while I wait for a Bricklink order so that I can continue to work on my tower roofs, I'm documenting my technique.

The Wizard's Tower

The Wizard's Tower shows off some of the features that can be accomplished with this design. One of the large goals was to provide access to interior spaces. Unfortunately, the Wizard's Tower is incomplete at the moment. The interiors on the lower part of the central tower are yet to be constructed, but I can at least show off the break-away wall sections allowing access to the interior.

The Basic Trick

The tower is made by taking long strips with 2x2 tiles attached and connecting them to a central core. There are three functional components: the core, the facade, and the filler. The core is just the inner ring of tank tread. The facade is the outer shell, usually just made of 2x2 tiles. The filler is everything in between. Exactly how the filler is constructed is less important than the distance between the core and the facade. More filler means bigger tower. Less filler means smaller tower.

The two above examples show two different sizes with different amounts of filler. For the sake of convenience, call the first example a "size 30 tower", and call the second example a "size 39 tower". The size 30 tower has a circumference of 30 tiles and the core is made of 30 pieces of tank tread. The gap between the core and the facade is filled by a technic beam and a plate, the equivalent of 3.5 plates. The size 39 tower has a circumference of 39 tiles and a core made of 39 pieces of tank tread. The gap between the core and the facade is filled by a technic beam and a brick, the equivalent of 5.5 plates.

I try to get by with as little tank tread as possible. For one thing, it leaves more room for an interior. For another, tank tread is expensive. I usually put a full ring of tank treads on the top and a full ring on the bottom of the tower, and use a just a strip of tank tread to patch up places that wouldn't hold together otherwise.


Cutting a single hole in the tower is straightforward, as long as you don't cut into the rings of tank tread. The large hole on the left stops just short of the top and bottom rings of tank tread. If the hole was far away from the bottom ring, the facade might splay outward and require some additional reinforcement to stay together. In the pictures below, the hole for the balcony is built similarly. The hole for the window is reinforced a bit by the fact that the window construction fits snugly into the hole, although I doubt the facade was at much risk of splaying outward.

To have one hole above another takes some planning. Here I have strips of tank tread holding together the stuff between the holes, as can be seen a few pictures back. To hide the tank tread, I had to make the holes at least 5 studs apart. There is some sagging here, but it's not too bad.

Tiles vs. Plates

Most of the time I use tiles for the facade, but I figured I could replace a tile with a plate with no problems, right? Wrong. Since a tile has that groove at the bottom, the plate needs just a bit more room. It's not much, but when you multiply it by 30, it can make a difference. I'm fairly certain this isn't a problem with the size 39 tower, but it was for the size 30 tower. On the top of the tower to the left you'll see that I alternate between plates and tiles. My original design was just plates, and if you look closely at some of the pictures here they show the old design. The original design didn't work; there wasn't enough room for the plates and as a consequence some of the plates were not firmly attached and kept falling off.

But now that we know this, maybe it could be used to our advantage. One possible issue with this whole method is that a size 30 tower's circumference is not exactly 30, a size 39's circumference is not exactly 39. For sizes 30 and 39, this hasn't been a big problem, but should we run into a tower where the fit is too loose, we might add plates in strategic places to tighten it up a little. The size 18 towers in the Wizard's Tower are loose enough for gaps to crop up; some plates may help to even out the spacing.

Wall sections

Let's talk a bit about geometry and why the above stuff works. Whenever two pieces of tank tread snap together, the angle between the two pieces has many possibilities. It's our job to limit these possibilities and get the angle to be more or less what we want it to be. The tiles on the facade force this angle to turn inwards. The facade on the size 30 tower forces the second tank tread to turn inwards by at least 12 degrees (approx). Now when the ring of tank tread is completed, these turns must add up to exactly 360 degrees. It's not too difficult to show that the last two statements imply that at each connection, the direction changes by 12 degrees (approx).

The facade makes the tank tread turn. The fact that we have a closed circuit keeps it from turning too far. This means that if we don't want a complete circuit we have to find another way to keep the tank tread from turning too far. The quick and dirty solution: a brace to hold the two ends of the wall apart.

The example pictured is based on the size 30 tower. The curvature of the example is almost the same as the curvature of the size 30 tower, but not quite. This is because the brace pushes the tiles together more tightly, and thus changes it just a bit. It's not severe enough to try to fix in this example, but is something to be aware of.

Small Towers

The most straight forward way to make smaller towers in to replace the tank tread we've been using with smaller tank tread, then adapt the techniques we've already seen. However, the small towers in the Wizard's Tower use the method I've already documented here. It's a terrible trick if you want to have an interior, but otherwise it's a cool little trick.


Ignore the roofs in the pictures here, I have since refined the design and documented it here. I'm still looking for something better, but for now this is what I've got.

Other Methods

Bricks and Cylinders

The most ubiquitous technique is the old brick and cylinder trick. There are two basic types, one with 1x2 bricks and one with 1x3 bricks. For example, this one and this one by Eggy Pop.

Just Bricks

The most straightforward way to make a round wall is to build a straight wall out of 1x2 bricks and bend it into a circle. The bricks only bend so far, so this makes large diameter walls. The Wizard's Tower uses this trick for the outer walls. The smallest of these walls has a circumference of 96 bricks, but smaller (Eggy Pop again) circles are possible. How small you make the wall depends on how skittish you are about damaging bricks. For the serious enthusiast, check out

Deborah Higdon

Deborah Higdon devised an interesting method which gives a look similar to my method. (The rest of her photostream is also worth checking out.) This technique has shown up at least twice, here by busboy489, and here by Jordan Schwartz.

Nannan Z

Nannan Z has an awesome variation that he used on this creation. The technique is perfect for making a snot wall that is just two studs high. It is parts intensive, and I'm impressed by the number of pieces used in his MOC to build that tower.

Small Towers

Here bikicsmilan offers a method for creating small towers with also gives a look similar to my technique. I plan on playing with this myself sometime in the near future.

Other scattered examples

Here's a fun one by Nathan Todd.

Bruce N H brought this one (by Nyu) to my attention back when I first started experimenting with round towers.

More fun with tank tread, by TooMuchCaffeine.

I accidentally ran across this one by Derfel Cadarn.

Here's a cool one by Hinckley et. al. On page 2 there's a picture of the round part from the inside for you to suss out how it's done.


 I like it 
  January 18, 2018
Very helpful and interesting post, thanks!
 I like it 
  May 11, 2015
Awesome tutorial. Will have to try this once or twice. Had a great time at Brick Magic 2015 this weekend.
 I like it 
  October 22, 2013
Well explained tutorial. The fact that the groove of tiles often makes clean edges possible is a good thing, but sometimes a horror, when you need a plate instead - this confronts me from time to time, too. byside its always a concerne for the costs of a project to change from bricks to tiles, but as i see now, its worth.
 I like it 
  June 7, 2013
A fascinating and well written tutorial, with lots of links to helpful examples. Thank you for taking the time to put this together: it's an incredible resource for people like me, who want to build Lego cylinders.
 I like it 
  June 8, 2012
1.-your castle is incredible! it looks beautiful! 2.-thank you for taking time to share this really interessting and so helpfull collection of technics and examples...
 I like it 
  March 18, 2012
John Boozer
 I like it 
White Knight
  March 29, 2011
this is really good, interesting looking model too ....
 I made it 
  March 17, 2011
Quoting Allan Hall I'v seen this before, you get a better internal wall than the method I use, I might look at this again. many thanks.
Do you remember where you saw it?
 I like it 
  March 17, 2011
I'v seen this before, you get a better internal wall than the method I use, I might look at this again. many thanks.
 I like it 
  March 16, 2011
I think I'm ready to live here now...
 I like it 
  March 15, 2011
Well presented, Dude!
 I like it 
  March 15, 2011
That's one good castle you made there. The techniques involved are genius.
 I like it 
  March 15, 2011
Great use of the tracks! Nice smooth curves annd NO HOLES! I was looking into ways to avoid the use of alternating a 2x1x1 brick and a 1x1x1 round brick to create round towers. I also came up with the 2x2 tiles but did not manage to make a decent tower. Next step, see if I can still incorporate something similar into my designs. cheers KJ
 I like it 
  March 15, 2011
Brilliant idea! The tower looks great and we all aAppreciate the fact you are sharing this!
 I like it 
  March 15, 2011
Ya know, I actually tried using the tank treads to make some rounded walls once but the treads didn't hold together well. I think I'll go back and try it again with your idea. Thanks so much for sharing! Ok... time to "fav" you... ~ Chris.
 I like it 
  March 15, 2011
(JAW.DROPS) dued this is the best castle ever i love it.....IF YOU LIKE STAR WARS SPACE VEHICALS AND COOL MINIFIGS COME TO MY PAGE!!!!
 I like it 
  March 15, 2011
Wow, this is an excellent way to create a round wall!
 I like it 
  March 15, 2011
Excellent, thanks to take time to explain us how you did!
 I like it 
  March 15, 2011
Fantastic article! Very extensive and very informative. One thing you have going for you is your experience. Looking at your amazing Wizards Castle up there gives loads of credibility to your already elaborate article. Well done and thank you!
 I like it 
  March 15, 2011
Dude this is great! Very creative.
 I like it 
  March 15, 2011
By John Boozer
Add to my favorite builders

people like this. See who.

71,198 visitors
Added March 14, 2011
 You are at the beginning of this folder. Round Tower 2
More from John
More across MOCpages

LEGO models my own creation MOCpages toys shop On Round Tower TechniquesCastle

You Your home page | LEGO creations | Favorite builders
Activity Activity | Comments | Creations
Explore Explore | Recent | Groups
MOCpages is an unofficial, fan-created website. LEGO® and the brick configuration are property of The LEGO Group, which does not sponsor, own, or endorse this site.
©2002-2018 Sean Kenney Design Inc | Privacy policy | Terms of use