MOCpages : Share your LEGO® creations
LEGO models my own creation MOCpages toys shop
Welcome to the world's greatest LEGO fan community!
Explore cool creations, share your own, and have lots of fun together.  ~  It's all free!
Comment on Centrifugal waterpump, a simple electric high volume pump.
Rate it
55555 Excellent  
I like it
4444 Very good
I like it
333 Good
22 Average
1 Not good
  (I'll rate it later)
First name Have a MOCapges account? Sign in
Last name
You'll need to check your e-mail before we post your comment.
Your e-mail won't be shown onscreen, and we will never sell or abuse it.
(No HTML, please)
  Use appropriate language and do not be mean, rude, or insulting.
Inappropriate comments will be deleted before anyone sees them,
and your account may be deleted. Full rules | Why?

Centrifugal waterpump, a simple electric high volume pump. . A centrifugal pump is a rotodynamic pump that uses a rotating impeller. . Pump of this type is known to me. Since impeller of centrifugal pump is a specific shape, lego has really little to offer. But I had some older type gears, red g9, blue g15 and yellow g21 ( Technic gear Expert Builder xx Tooth with axle hole ). So I just gave a try with these and they did throw water around. I built a casing around two g15 gears, some piping and an electric motor to power it. First tests show that it does work, but I got water all around table!! Lego bricks have some 0,1mm gaps and that is enough for water to leak. First protos leaked as much they pumped! The secret is to use fewer and bigger bricks to minimize gaps. And tape to cover some worst leaks. First protos had impeller in vertical position, but it wasn't a good idea. I turned it to horizontal position, so pump can stand in the water and leaking is no problem anymore. I used an old 9V motor type ( 2838c01 ) because it can rotate fast enough. I had to gear it a little bit down to get more torque and thus more pumping power. The Current version can pump to the height of 11 bricks about 4 litres/minute. It pumps water up to 20 brick height, but max practical height is about 15. By adding a second motor it gets more power but gears make it noisy. With this you can make a realistic lego river/waterfall ;) Water lubricated gears, that little pneumatic hose feeds water back Water intake. Could be bigger, still searching the best shape. Pump inside. The gears simply throws water down right to discharge pipe Twin-motor test. It rews faster, but pumps only a little bit more. Probably discharge pipe should be also wider and intake too. The Train speed regulator I use has 6 speeds and 5. speed gives already full flow. Another twin-motor test. Original motor + direct drive motor. But,I discovered that water intake was a problem. There is only 1 brick distance from pump intake to the bottom. I increased it to 2 bricks and it doubled the flow !! This one pumps to height of 21 bricks 2,6 liters/min !! I retested the original pump and now it pumps 4,5 liters/min !! Tuning this pump is an endless job ;) A LDD-picture of another pump model. This model uses 21-tooth gears. chamber is made of 2339 and 30099 bricks and it's perfectly round. Gap between gears and chamber is about 2mm, should be very tight. Not tested in real life yet, but I expect this to be very good pump. First Test: about 4,5L/min to height of 14 bricks !! intake may still be too small. But these panels, 2 x 2, are leaking terribly, so i have to use tape ;) Pump model with XL-motor, lot of changes since first proto. Pumps 6,5 liters/min. And in real life, pumping 6,5 liters/min ( This has now separate page + video ) See how the pump works!

LEGO models my own creation MOCpages toys shop

You Your home page | LEGO creations | Favorite builders
Activity Activity | Comments | Creations
Explore Explore | Recent | Groups
MOCpages is an unofficial, fan-created website. LEGO® and the brick configuration are property of The LEGO Group, which does not sponsor, own, or endorse this site.
©2002-2018 Sean Kenney Design Inc | Privacy policy | Terms of use